Harness - Body - LH (Remove and Replace)

Correction code 1710080217100802

Remove

  1. Remove the sill rear trunk trim. See Trim - Sill - Trunk (Remove and Replace).
  2. Remove the 2nd row LH seat back assembly. See Seat Back - 2nd Row - LH (Remove and Install).
  3. Remove the 2nd row RH seat back assembly. See Seat Back - 2nd Row - RH (Remove and Install).
  4. Release the trunk carpet clips from the body studs under the 2nd row seat cushion.
  5. Release the clips that attach the trunk carpet to the body, and then remove the trunk carpet from the vehicle.
  6. Remove the LH side rear trunk trim. See Trim - Side - Trunk - LH (Remove and Replace).
  7. Remove the RH side rear trunk trim. See Trim - Side - Trunk - RH (Remove and Replace).
  8. Remove the rear fascia assembly. See Fascia - Rear (Remove and Install).
  9. Remove the clips that attach the LH body harness to the body in the rear fascia and rear subframe areas.
  10. Disconnect the electrical harness from the rear Bluetooth passive entry antenna connector.
  11. Disconnect the electrical harness from the rear subframe electrical harness connector and the LH electric parking brake connector.
  12. Release the clips that attach the electrical harness to the body, and then push the rear subframe portion of the electrical harness through the LH side trunk bulkhead.
    Note: The LH body harness passes through the trunk near the rear section of the rear LH wheel liner area.
  13. Lower the vehicle.
  14. With an assistant, remove the vehicle from the lift.
    Caution:
    The vehicle is safely pushed for only a very short distance and at a very slow speed.
  15. Position wheel chocks.
  16. Open all doors.
  17. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  18. Remove the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  19. Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  20. Remove the LH footwell cover. See Cover - Footwell - Driver (Remove and Replace).
  21. Remove the LH footwell duct. See Duct - Footwell - LH (Remove and Replace).
  22. Remove the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace)
  23. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  24. Remove the RH footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  25. Perform the vehicle electrical isolation procedure. See Vehicle Electrical Isolation Procedure.
  26. Remove the driver and front passenger seats. See Seat - Driver (Remove and Replace).
  27. Remove the center console assembly. See Center Console (Remove and Install).
  28. Remove the driver's knee airbag. See Airbag - Knee - Driver (Remove and Replace).
  29. Remove the rear LH sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  30. Remove the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  31. Remove the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  32. Remove the LH B-pillar applique. See Applique - B-Pillar - LH (Remove and Replace).
  33. Remove the LH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
  34. Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  35. Remove the RH rear sill trim. See Trim - Sill Panel - Rear - LH (Remove and Replace)
  36. Remove the RH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  37. Remove the RH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  38. Remove the RH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
  39. Remove the RH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  40. Remove the LH and RH rear C-pillar trim. See Trim - C-Pillar - Rear - LH (Remove and Replace).
  41. Release the clips that attach the package tray electrical harness to the body in the upper C-pillar area.
  42. Disconnect the package tray electrical harness from the RH body harness connector.
  43. Release the clip, and then disconnect the package tray speaker electrical harness from the tuner connectors.
  44. Release the clip that attaches the package tray electrical harness to the LH C-pillar.
  45. Disconnect the electrical harness from the antenna amplifier connector.
  46. Remove the package tray trim. See Trim - Package Tray (Remove and Install).
  47. Release the clips that attach the LH and RH sides of the rear main cabin carpet to the body.
  48. Release the clips that attach the front LH main cabin carpet to the body, and then remove the carpet from the vehicle.
  49. Disconnect the electrical harness from the accelerator and the brake pedal connectors.
  50. Release the clips that attach the electrical harness to the body under the IP carrier area.
  51. Remove and discard the bolt that attaches the electrical harness ground strap at the driver footwell area.
  52. Disconnect the electrical harness from the LH body controller module connectors.
  53. Release the clips that attach the electrical harnessto the body in the LH body controller module area.
  54. Release the clips that attach the electrical harness to the body in the LH lower B-pillar areas.
  55. Lift up the rear portion of the floor duct to release the clips that attach the electrical harness to the body.
  56. Release the clips that attach the electrical harness to the body under the front LH seat and RH lower B-pillar areas.
  57. Disconnect the electrical harness from the connectors in the RH lower B-pillar area.
  58. Disconnect the electrical harness from the passive supplemental restraint control module connector.
  59. Remove and discard the bolt that attaches the electrical harness ground strap to the body in the LH lower B-pillar area.
  60. Release the clips that attach the harness to the body in the B-pillar area.
  61. Disconnect the electrical harness from the LH door connector and the front LH seat belt connector.
  62. Release the clips that attach the harness to the body in the lower C-pillar area.
  63. Disconnect the electrical harness from the connectors in the lower C-pillar area.
  64. Release the clips that attach the electrical harness to the body in the LH side curtain airbag and TPMS module areas.
  65. Disconnect the electrical harness from the LH side curtain airbag connector.
  66. Disconnect the electrical harness from the TPMS module connector.
  67. Disconnect the electrical harness from LH rear seat belt connector.
  68. Release the clips that attach the electrical harness to the body in the LH side trunk area.
  69. Disconnect the electrical harness from the charge port ECU connectors.
  70. Remove and discard the bolt that attaches the harness ground strap to the body in the charge port area.
  71. Remove the LH body harness from the vehicle.
1Remove the sill rear trunk trim. See Trim - Sill - Trunk (Remove and Replace).
2Remove the 2nd row LH seat back assembly. See Seat Back - 2nd Row - LH (Remove and Install).
3Remove the 2nd row RH seat back assembly. See Seat Back - 2nd Row - RH (Remove and Install).
4Release the trunk carpet clips from the body studs under the 2nd row seat cushion.
5Release the clips that attach the trunk carpet to the body, and then remove the trunk carpet from the vehicle.
6Remove the LH side rear trunk trim. See Trim - Side - Trunk - LH (Remove and Replace).
7Remove the RH side rear trunk trim. See Trim - Side - Trunk - RH (Remove and Replace).
8Remove the rear fascia assembly. See Fascia - Rear (Remove and Install).
9Remove the clips that attach the LH body harness to the body in the rear fascia and rear subframe areas.
10Disconnect the electrical harness from the rear Bluetooth passive entry antenna connector.
11Disconnect the electrical harness from the rear subframe electrical harness connector and the LH electric parking brake connector.
12Release the clips that attach the electrical harness to the body, and then push the rear subframe portion of the electrical harness through the LH side trunk bulkhead.
Note: The LH body harness passes through the trunk near the rear section of the rear LH wheel liner area.
13Lower the vehicle.
14With an assistant, remove the vehicle from the lift.
Caution:
The vehicle is safely pushed for only a very short distance and at a very slow speed.
15Position wheel chocks.
16Open all doors.
17Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
18Remove the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
19Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
20Remove the LH footwell cover. See Cover - Footwell - Driver (Remove and Replace).
21Remove the LH footwell duct. See Duct - Footwell - LH (Remove and Replace).
22Remove the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace)
23Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
24Remove the RH footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
25Perform the vehicle electrical isolation procedure. See Vehicle Electrical Isolation Procedure.
26Remove the driver and front passenger seats. See Seat - Driver (Remove and Replace).
27Remove the center console assembly. See Center Console (Remove and Install).
28Remove the driver's knee airbag. See Airbag - Knee - Driver (Remove and Replace).
29Remove the rear LH sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
30Remove the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
31Remove the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
32Remove the LH B-pillar applique. See Applique - B-Pillar - LH (Remove and Replace).
33Remove the LH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
34Remove the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
35Remove the RH rear sill trim. See Trim - Sill Panel - Rear - LH (Remove and Replace)
36Remove the RH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
37Remove the RH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
38Remove the RH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
39Remove the RH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
40Remove the LH and RH rear C-pillar trim. See Trim - C-Pillar - Rear - LH (Remove and Replace).
41Release the clips that attach the package tray electrical harness to the body in the upper C-pillar area.
42Disconnect the package tray electrical harness from the RH body harness connector.
43Release the clip, and then disconnect the package tray speaker electrical harness from the tuner connectors.
44Release the clip that attaches the package tray electrical harness to the LH C-pillar.
45Disconnect the electrical harness from the antenna amplifier connector.
46Remove the package tray trim. See Trim - Package Tray (Remove and Install).
47Release the clips that attach the LH and RH sides of the rear main cabin carpet to the body.
48Release the clips that attach the front LH main cabin carpet to the body, and then remove the carpet from the vehicle.
49Disconnect the electrical harness from the accelerator and the brake pedal connectors.
50Release the clips that attach the electrical harness to the body under the IP carrier area.
51Remove and discard the bolt that attaches the electrical harness ground strap at the driver footwell area.
52Disconnect the electrical harness from the LH body controller module connectors.
53Release the clips that attach the electrical harnessto the body in the LH body controller module area.
54Release the clips that attach the electrical harness to the body in the LH lower B-pillar areas.
55Lift up the rear portion of the floor duct to release the clips that attach the electrical harness to the body.
56Release the clips that attach the electrical harness to the body under the front LH seat and RH lower B-pillar areas.
57Disconnect the electrical harness from the connectors in the RH lower B-pillar area.
58Disconnect the electrical harness from the passive supplemental restraint control module connector.
59Remove and discard the bolt that attaches the electrical harness ground strap to the body in the LH lower B-pillar area.
60Release the clips that attach the harness to the body in the B-pillar area.
61Disconnect the electrical harness from the LH door connector and the front LH seat belt connector.
62Release the clips that attach the harness to the body in the lower C-pillar area.
63Disconnect the electrical harness from the connectors in the lower C-pillar area.
64Release the clips that attach the electrical harness to the body in the LH side curtain airbag and TPMS module areas.
65Disconnect the electrical harness from the LH side curtain airbag connector.
66Disconnect the electrical harness from the TPMS module connector.
67Disconnect the electrical harness from LH rear seat belt connector.
68Release the clips that attach the electrical harness to the body in the LH side trunk area.
69Disconnect the electrical harness from the charge port ECU connectors.
70Remove and discard the bolt that attaches the harness ground strap to the body in the charge port area.
71Remove the LH body harness from the vehicle.

Install

  1. Install the LH body harness into the vehicle.
  2. Install a new bolt to attach the electrical harness ground strap to the body in the charge port area.
    Torque 8 Nm
  3. Connect the electrical harness to the charge port ECU connectors.
  4. Fasten the clips that attach the electrical harness to the body in the LH side trunk area.
  5. Connect the electrical harness to LH rear seat belt connector.
  6. Connect the electrical harness to the TPMS module connector.
  7. Connect the electrical harness to the LH side curtain airbag connector.
  8. Fasten the clips that attach the electrical harness to the body in the LH side curtain airbag and TPMS module areas.
  9. Connect the electrical harness to the connectors in the lower C-pillar area.
  10. Fasten the clips that attach the harness to the body in the lower C-pillar area.
  11. Connect the electrical harness to the LH door connector and the front LH seat belt connector.
  12. Fasten the clips that attach the harness to the body in the B-pillar area.
  13. Install a new bolt to attach the electrical harness ground strap to the body in the LH lower B-pillar area.
    Torque 8 Nm
  14. Connect the electrical harness to the passive supplemental restraint control module connector.
  15. Connect the electrical harness to the connectors in the RH lower B-pillar area.
  16. Fasten the clips that attach the electrical harness to the body under the front LH seat and RH lower B-pillar areas.
  17. Fasten the clips that attach the electrical harness to the body under the rear portion of the floor duct.
  18. Fasten the clips that attach the electrical harness to the body in the LH lower B-pillar areas.
  19. Fasten the clips that attach the electrical harness to the body in the LH body controller module area.
  20. Connect the electrical harness to the LH body controller module connectors.
  21. Install a new bolt to attach the electrical harness ground strap to the body in the driver footwell area.
    Torque 8 Nm
  22. Fasten the clips that attach the electrical harness to the body under the IP carrier area.
  23. Connect the electrical harness to the accelerator and the brake pedal connectors.
  24. Install the carpet into the vehicle, and then fasten the clips that attach the front LH main cabin carpet to the body.
  25. Fasten the clips that attach the LH and RH sides of the rear main cabin carpet to the body.
  26. Install the package tray trim. See Trim - Package Tray (Remove and Install).
  27. Connect the electrical harness to the antenna amplifier connector.
  28. Fasten the clip that attaches the package tray electrical harness to the LH C-pillar.
  29. Connect the package tray speaker electrical harness to the tuner connectors, and then fasten the clip.
  30. Connect the package tray electrical harness to the RH body harness connector.
  31. Fasten the clips that attach the package tray electrical harness to the body in the upper C-pillar area.
  32. Install the LH and RH rear C-pillar trim. See Trim - C-Pillar - Rear - LH (Remove and Replace).
  33. Install the RH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  34. Install the RH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
  35. Install the RH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  36. Install the RH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  37. Install the RH rear sill trim. See Trim - Sill Panel - Rear - LH (Remove and Replace)
  38. Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
  39. Install the LH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
  40. Install the LH B-pillar applique. See Applique - B-Pillar - LH (Remove and Replace).
  41. Install the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
  42. Install the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
  43. Install the rear LH sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
  44. Install the driver's knee airbag. See Airbag - Knee - Driver (Remove and Replace).
  45. Install the center console assembly. See Center Console (Remove and Install).
  46. Install the driver and front passenger seats. See Seat - Driver (Remove and Replace).
  47. Install the RH footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  48. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  49. Install the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace)
  50. Install the LH footwell duct. See Duct - Footwell - LH (Remove and Replace).
  51. Install the LH footwell cover. See Cover - Footwell - Driver (Remove and Replace).
  52. Install the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  53. Install the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  54. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  55. Partially close all doors.
  56. Remove the wheel chocks.
  57. With an assistant, move the vehicle to the lift.
    Caution:
    The vehicle is safely pushed for only a very short distance and at a very slow speed.
  58. Raise the vehicle.
  59. Move the rear subframe portion of the electrical harness in through the LH side trunk bulkhead, and then fasten the clips that attach the electrical harness to the body.
    Note: The LH body harness passes through the trunk near the rear section of the rear LH wheel liner area.
  60. Connect the electrical harness to the rear subframe electrical harness connector and the LH electric parking brake connector.
  61. Connect the electrical harness to the rear Bluetooth passive entry antenna connector.
  62. Install the clips that attach the LH body harness to the body in the rear fascia and rear subframe areas.
  63. Install the rear fascia assembly. See Fascia - Rear (Remove and Install).
  64. Lower the vehicle.
  65. Install the LH and RH trunk side trims. See Trim - Side - Trunk - LH (Remove and Replace).
  66. Install the trunk carpet into the trunk, and then fasten the clips that attach the trunk carpet to the body.
  67. Fasten the trunk carpet clips to the body studs under the 2nd row seat cushion.
  68. Install the 2nd row RH seat back assembly. See Seat Back - 2nd Row - RH (Remove and Install).
  69. Install the 2nd row LH seat back assembly. See Seat Back - 2nd Row - LH (Remove and Install).
  70. Install the sill rear trunk trim. See Trim - Sill - Trunk (Remove and Replace).
  71. Connect 12V power. See 12V Power (Disconnect and Connect).
1Install the LH body harness into the vehicle.
2Install a new bolt to attach the electrical harness ground strap to the body in the charge port area.
Torque 8 Nm
3Connect the electrical harness to the charge port ECU connectors.
4Fasten the clips that attach the electrical harness to the body in the LH side trunk area.
5Connect the electrical harness to LH rear seat belt connector.
6Connect the electrical harness to the TPMS module connector.
7Connect the electrical harness to the LH side curtain airbag connector.
8Fasten the clips that attach the electrical harness to the body in the LH side curtain airbag and TPMS module areas.
9Connect the electrical harness to the connectors in the lower C-pillar area.
10Fasten the clips that attach the harness to the body in the lower C-pillar area.
11Connect the electrical harness to the LH door connector and the front LH seat belt connector.
12Fasten the clips that attach the harness to the body in the B-pillar area.
13Install a new bolt to attach the electrical harness ground strap to the body in the LH lower B-pillar area.
Torque 8 Nm
14Connect the electrical harness to the passive supplemental restraint control module connector.
15Connect the electrical harness to the connectors in the RH lower B-pillar area.
16Fasten the clips that attach the electrical harness to the body under the front LH seat and RH lower B-pillar areas.
17Fasten the clips that attach the electrical harness to the body under the rear portion of the floor duct.
18Fasten the clips that attach the electrical harness to the body in the LH lower B-pillar areas.
19Fasten the clips that attach the electrical harness to the body in the LH body controller module area.
20Connect the electrical harness to the LH body controller module connectors.
21Install a new bolt to attach the electrical harness ground strap to the body in the driver footwell area.
Torque 8 Nm
22Fasten the clips that attach the electrical harness to the body under the IP carrier area.
23Connect the electrical harness to the accelerator and the brake pedal connectors.
24Install the carpet into the vehicle, and then fasten the clips that attach the front LH main cabin carpet to the body.
25Fasten the clips that attach the LH and RH sides of the rear main cabin carpet to the body.
26Install the package tray trim. See Trim - Package Tray (Remove and Install).
27Connect the electrical harness to the antenna amplifier connector.
28Fasten the clip that attaches the package tray electrical harness to the LH C-pillar.
29Connect the package tray speaker electrical harness to the tuner connectors, and then fasten the clip.
30Connect the package tray electrical harness to the RH body harness connector.
31Fasten the clips that attach the package tray electrical harness to the body in the upper C-pillar area.
32Install the LH and RH rear C-pillar trim. See Trim - C-Pillar - Rear - LH (Remove and Replace).
33Install the RH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
34Install the RH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
35Install the RH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
36Install the RH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
37Install the RH rear sill trim. See Trim - Sill Panel - Rear - LH (Remove and Replace)
38Install the LH upper C-pillar trim. See Trim - C-Pillar - Upper - LH (Remove and Replace).
39Install the LH side rail trim. See Trim - Side Rail - LH (Remove and Replace).
40Install the LH B-pillar applique. See Applique - B-Pillar - LH (Remove and Replace).
41Install the LH lower B-pillar trim. See Trim - B-Pillar - Lower - LH (Remove and Replace).
42Install the LH upper B-pillar trim. See Trim - B-Pillar - Upper - LH (Remove and Replace).
43Install the rear LH sill panel trim. See Trim - Sill Panel - Rear - LH (Remove and Replace).
44Install the driver's knee airbag. See Airbag - Knee - Driver (Remove and Replace).
45Install the center console assembly. See Center Console (Remove and Install).
46Install the driver and front passenger seats. See Seat - Driver (Remove and Replace).
47Install the RH footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
48Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
49Install the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace)
50Install the LH footwell duct. See Duct - Footwell - LH (Remove and Replace).
51Install the LH footwell cover. See Cover - Footwell - Driver (Remove and Replace).
52Install the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
53Install the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
54Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
55Partially close all doors.
56Remove the wheel chocks.
57With an assistant, move the vehicle to the lift.
Caution:
The vehicle is safely pushed for only a very short distance and at a very slow speed.
58Raise the vehicle.
59Move the rear subframe portion of the electrical harness in through the LH side trunk bulkhead, and then fasten the clips that attach the electrical harness to the body.
Note: The LH body harness passes through the trunk near the rear section of the rear LH wheel liner area.
60Connect the electrical harness to the rear subframe electrical harness connector and the LH electric parking brake connector.
61Connect the electrical harness to the rear Bluetooth passive entry antenna connector.
62Install the clips that attach the LH body harness to the body in the rear fascia and rear subframe areas.
63Install the rear fascia assembly. See Fascia - Rear (Remove and Install).
64Lower the vehicle.
65Install the LH and RH trunk side trims. See Trim - Side - Trunk - LH (Remove and Replace).
66Install the trunk carpet into the trunk, and then fasten the clips that attach the trunk carpet to the body.
67Fasten the trunk carpet clips to the body studs under the 2nd row seat cushion.
68Install the 2nd row RH seat back assembly. See Seat Back - 2nd Row - RH (Remove and Install).
69Install the 2nd row LH seat back assembly. See Seat Back - 2nd Row - LH (Remove and Install).
70Install the sill rear trunk trim. See Trim - Sill - Trunk (Remove and Replace).
71Connect 12V power. See 12V Power (Disconnect and Connect).