Glove Box (LHD) (Remove and Replace)

Correction code 1405100214051002

Remove

  1. Remove and secure the customer's belongings from the glove box, if needed.
  2. Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  3. Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  4. Disconnect 12V power. See 12V Power (Disconnect and Connect).
  5. Remove the LH and RH instrument panel end caps. See End Cap - Instrument Panel - LH (Remove and Replace).
  6. Remove the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  7. Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  8. Remove the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  9. Remove the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace).
  10. Remove the main instrument panel decor trim. See Decor Trim - Instrument Panel - Main (Remove and Replace).
  11. Remove the screws (x6) that attach the glove box to the IP carrier.
  12. Release the clips that attach the glove box to the IP carrier.
  13. Disconnect the electrical harness from the glove box solenoid connector, the damper connector, and the puddle light connector.
    Note: 2 of the electrical connectors are accessed from the bottom of the instrument panel.
  14. Remove the glove box from the vehicle.
1Remove and secure the customer's belongings from the glove box, if needed.
2Remove the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
3Remove the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
4Disconnect 12V power. See 12V Power (Disconnect and Connect).
5Remove the LH and RH instrument panel end caps. See End Cap - Instrument Panel - LH (Remove and Replace).
6Remove the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
7Remove the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
8Remove the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
9Remove the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace).
10Remove the main instrument panel decor trim. See Decor Trim - Instrument Panel - Main (Remove and Replace).
11Remove the screws (x6) that attach the glove box to the IP carrier.
12Release the clips that attach the glove box to the IP carrier.
13Disconnect the electrical harness from the glove box solenoid connector, the damper connector, and the puddle light connector.
Note: 2 of the electrical connectors are accessed from the bottom of the instrument panel.
14Remove the glove box from the vehicle.

Install

  1. Bring the glove box into the vehicle, and then connect the electrical harness to the glove box solenoid connector, the damper connector, and the puddle light connector.
    Note: 2 of the electrical connectors are accessed from the bottom of the instrument panel.
    Note: Route the puddle lamp electrical harness as illustrated.
    Glove box harness connectors
    Puddle lamp harness routing
  2. Make sure that the glove box damper pin is fully seated, and not to bump the glove box damper when installing the glove box.
  3. Fasten the clips that attach the glove box to the IP carrier.
  4. Install the screws (x6) that attach the glove box to the IP carrier.
    Torque 2.3 Nm
  5. Install the main instrument panel decor trim. See Decor Trim - Instrument Panel - Main (Remove and Replace).
  6. Install the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace).
  7. Install the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
  8. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  9. Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  10. Install the LH and RH instrument panel end caps. See End Cap - Instrument Panel - LH (Remove and Replace).
  11. Reconnect 12V power. See 12V Power (Disconnect and Connect).
  12. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
  13. Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
  14. Verify that the glove box door opens normally through the touchscreen.
  15. Return the customer's belongings in the glove box, if needed.
Glove box harness connectors
Puddle lamp harness routing
1Bring the glove box into the vehicle, and then connect the electrical harness to the glove box solenoid connector, the damper connector, and the puddle light connector.
Note: 2 of the electrical connectors are accessed from the bottom of the instrument panel.
Note: Route the puddle lamp electrical harness as illustrated.
2Make sure that the glove box damper pin is fully seated, and not to bump the glove box damper when installing the glove box.
3Fasten the clips that attach the glove box to the IP carrier.
4Install the screws (x6) that attach the glove box to the IP carrier.
Torque 2.3 Nm
5Install the main instrument panel decor trim. See Decor Trim - Instrument Panel - Main (Remove and Replace).
6Install the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace).
7Install the passenger footwell cover. See Cover - Footwell - Passenger (LHD) (Remove and Replace).
8Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
9Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
10Install the LH and RH instrument panel end caps. See End Cap - Instrument Panel - LH (Remove and Replace).
11Reconnect 12V power. See 12V Power (Disconnect and Connect).
12Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace).
13Install the 2nd row lower seat cushion. See Seat Cushion - Lower - 2nd Row (Remove and Replace).
14Verify that the glove box door opens normally through the touchscreen.
15Return the customer's belongings in the glove box, if needed.