Harness - Main Front (Remove and Replace)

Correction code 1710070217100702

Remove

  1. Open the front LH and front RH doors.
  2. Open the hood.
  3. Place wheel chocks on both rear wheels.
  4. Put vehicle in Neutral.
  5. Disconnect 12V power. See 12V Power (Disconnect and Connect).
  6. Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  7. Remove the driver knee airbag. See Airbag - Knee - Driver (Remove and Install).
  8. Release the clips that attach the footrest.
  9. Remove the RH knee airbag. See Airbag - Knee - Driver (Remove and Replace).
  10. Remove the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace)
  11. Remove the main instrument panel decor. See Decor Trim - Instrument Panel - Main (Remove and Replace).
  12. Remove the glove box. See Glove Box (LHD) (Remove and Replace).
  13. Remove the RH footwell duct. See Duct - Footwell - RH (Remove and Replace).
  14. Remove the RH air wave duct. See Duct - Air Wave - RH (Remove and Replace).
  15. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  16. Remove the 12V auxiliary battery. SeeBattery - 12V (Remove and Replace).
  17. Remove the nut that attaches the 12V battery rear hook tie down.
  18. Remove the wiper motor assembly. See Wiper Motor (Remove and Replace).
  19. Remove the bolt that attaches the thermal harness cover to the front body controller module, and then remove the cover from the module.
  20. Disconnect the thermal harness from the front body controller module connector.
  21. Release the clip that attaches the suction/liquid lines to the body near the TXV, and then move the electrical harness aside to gain access to the front body controller module.
  22. Remove the bolts that attach the front body controller module cover to the front body controller module, and then remove the cover.
  23. Disconnect the main front harness from the front body controller module connectors.
  24. Remove and discard the nuts (x6) and bolt that attach the power and ground cables to the front body controller module.
  25. Remove the bolts that attach the front body controller module to the body.
  26. Release the clips that attach the bottom of the front body controller module to the body, and then remove the lower busbar from the stud.
  27. Remove the bolt that attaches the ground strap to the upper rear of the front body controller module, and then remove the ground strap from the module.
  28. Remove the bolt that attaches the ground strap to the lower right side of the front body controller module, and then remove the ground strap from the module.
  29. Remove the bolt that attaches the ground strap to the lower rear of the front body controller module, and then remove the module from the vehicle.
  30. Remove the 12V battery bracket. See Bracket - 12V Battery (RWD) (Remove and Replace).
  31. Release the clips that attach the HVAC plenum outer duct to the HVAC plenum inner duct, and then remove the outer duct.
  32. Remove the fasteners that attach the HVAC plenum inner duct to the body, and then remove the inner duct from the vehicle.
  33. Disconnect the electrical harness from the RH body controller module connector.
  34. Remove and discard the nuts (x2) that attach the power cables of the electrical harness to the RH body controller module, and remove the power cables from the module.
  35. Remove and discard the nut that attaches the RH body controller module to the A-pillar, and lower the module for access.
  36. Release the clip that attaches the inline electrical harness connector to the RH body controller module, and then disconnect the electrical connector.
  37. Release the clips that attach the electrical harness to the car computer.
  38. Disconnect the electrical harness from the car computer connectors (x7).
  39. Push the RH side of the electrical harness out through the bulkhead.
  40. Disconnect the electrical harness from the LH body controller module connector.
  41. Remove and discard the nut that attaches the power cable of the electrical harness to the LH body controller module, and remove the power cable from the module.
  42. Release the clip that attaches the inline electrical harness connector X909 to the LH body controller module, and then disconnect the electrical connector.
  43. Push the LH side of the electrical harness out through the bulkhead.
  44. Release the clip that attaches the electrical harness to the body in the brake booster area.
  45. Disconnect the electrical harness from the connectors (x3) in the brake booster area.
  46. Disconnect the electrical harness from the brake booster connector.
  47. Disconnect the electrical harness from the ABS unit connector.
  48. Release the clips that attach the electrical harness to the body in the front LH frame rail area.
  49. Remove and discard the bolts (x4) that attach the electrical harness ground terminals to the body in the front LH frame rail area.
  50. Disconnect the electrical harness from the steering rack connectors and connectors in the front LH frame rail area.
  51. Disconnect the electrical harness from the LH headlight connector.
  52. Release the clips that attach the electrical harness to the body in the HVAC plenum duct area.
  53. Disconnect the electrical harness from the TXV connector.
  54. Remove the bolt that attaches the electrical harness ground terminal to the body in the TXV area
  55. Release the clips that attach the electrical harness to the body in the front RH frame rail area.
  56. Remove and discard the bolt that attaches the electrical harness ground terminal to the body in the front RH frame rail area.
  57. Release the clips that attach the electrical harness to the body in the RH headlight area.
  58. Disconnect the electrical harness from the RH headlight connector.
  59. Partially close all doors.
  60. Remove the wheel chocks.
  61. With an assistant, move the vehicle to a lift.
    Caution:
    The vehicle is safely pushed for only a very short distance and at a very slow speed.
  62. Remove the front LH and front RH wheels. See Wheel (Remove and Install).
  63. Remove the front LH and front RH arch liners. See Wheel Arch Liner - Front - LH (Remove and Replace).
  64. Disconnect the electrical harness from the connectors in the front RH fascia area.
  65. Release the clips that attach the electrical harness to the body at the front of the front RH wheel liner area.
  66. Disconnect the electrical harness from the connector at the front of the front RH wheel liner area.
  67. Release the clips that attach the electrical harness to the body at the rear of the front RH wheel liner area.
  68. Disconnect the electrical harness from the front RH side repeater lamp connector.
  69. Disconnect the electrical harness from the connectors in the front LH fascia area.
  70. Disconnect the electrical harness from the front end module connector.
  71. Release the clips that attach the electrical harness to the body in the front LH wheel liner area.
  72. Disconnect the electrical harness from the connectors at the front of the front LH wheel liner area.
  73. Release the clips that attach the electrical harness to the body in the front LH wheel area.
  74. Disconnect the electrical harness from the front LH side repeater lamp connector.
  75. Lower the vehicle.
  76. Release the clips that attach the electrical harness to the body in the front RH frame area.
  77. Release the clips that attach the electrical harness to the body in the bulkhead area.
  78. Disconnect the electrical harness from the connectors in the bulkhead area.
  79. Release the clips that attach the electrical harness to the body in the LH frame rail area.
  80. Route the LH side of the electrical harness from the wheel liner, through the underhood storage unit area, and to the front body controller module area.
  81. Route the RH side of the electrical harness from the wheel liner, through the underhood storage unit area, and to the front body controller module area.
  82. Remove the electrical harness from the vehicle.
1Open the front LH and front RH doors.
2Open the hood.
3Place wheel chocks on both rear wheels.
4Put vehicle in Neutral.
5Disconnect 12V power. See 12V Power (Disconnect and Connect).
6Remove the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
7Remove the driver knee airbag. See Airbag - Knee - Driver (Remove and Install).
8Release the clips that attach the footrest.
9Remove the RH knee airbag. See Airbag - Knee - Driver (Remove and Replace).
10Remove the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace)
11Remove the main instrument panel decor. See Decor Trim - Instrument Panel - Main (Remove and Replace).
12Remove the glove box. See Glove Box (LHD) (Remove and Replace).
13Remove the RH footwell duct. See Duct - Footwell - RH (Remove and Replace).
14Remove the RH air wave duct. See Duct - Air Wave - RH (Remove and Replace).
15Remove the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
16Remove the 12V auxiliary battery. SeeBattery - 12V (Remove and Replace).
17Remove the nut that attaches the 12V battery rear hook tie down.
18Remove the wiper motor assembly. See Wiper Motor (Remove and Replace).
19Remove the bolt that attaches the thermal harness cover to the front body controller module, and then remove the cover from the module.
20Disconnect the thermal harness from the front body controller module connector.
21Release the clip that attaches the suction/liquid lines to the body near the TXV, and then move the electrical harness aside to gain access to the front body controller module.
22Remove the bolts that attach the front body controller module cover to the front body controller module, and then remove the cover.
23Disconnect the main front harness from the front body controller module connectors.
24Remove and discard the nuts (x6) and bolt that attach the power and ground cables to the front body controller module.
25Remove the bolts that attach the front body controller module to the body.
26Release the clips that attach the bottom of the front body controller module to the body, and then remove the lower busbar from the stud.
27Remove the bolt that attaches the ground strap to the upper rear of the front body controller module, and then remove the ground strap from the module.
28Remove the bolt that attaches the ground strap to the lower right side of the front body controller module, and then remove the ground strap from the module.
29Remove the bolt that attaches the ground strap to the lower rear of the front body controller module, and then remove the module from the vehicle.
30Remove the 12V battery bracket. See Bracket - 12V Battery (RWD) (Remove and Replace).
31Release the clips that attach the HVAC plenum outer duct to the HVAC plenum inner duct, and then remove the outer duct.
32Remove the fasteners that attach the HVAC plenum inner duct to the body, and then remove the inner duct from the vehicle.
33Disconnect the electrical harness from the RH body controller module connector.
34Remove and discard the nuts (x2) that attach the power cables of the electrical harness to the RH body controller module, and remove the power cables from the module.
35Remove and discard the nut that attaches the RH body controller module to the A-pillar, and lower the module for access.
36Release the clip that attaches the inline electrical harness connector to the RH body controller module, and then disconnect the electrical connector.
37Release the clips that attach the electrical harness to the car computer.
38Disconnect the electrical harness from the car computer connectors (x7).
39Push the RH side of the electrical harness out through the bulkhead.
40Disconnect the electrical harness from the LH body controller module connector.
41Remove and discard the nut that attaches the power cable of the electrical harness to the LH body controller module, and remove the power cable from the module.
42Release the clip that attaches the inline electrical harness connector X909 to the LH body controller module, and then disconnect the electrical connector.
43Push the LH side of the electrical harness out through the bulkhead.
44Release the clip that attaches the electrical harness to the body in the brake booster area.
45Disconnect the electrical harness from the connectors (x3) in the brake booster area.
46Disconnect the electrical harness from the brake booster connector.
47Disconnect the electrical harness from the ABS unit connector.
48Release the clips that attach the electrical harness to the body in the front LH frame rail area.
49Remove and discard the bolts (x4) that attach the electrical harness ground terminals to the body in the front LH frame rail area.
50Disconnect the electrical harness from the steering rack connectors and connectors in the front LH frame rail area.
51Disconnect the electrical harness from the LH headlight connector.
52Release the clips that attach the electrical harness to the body in the HVAC plenum duct area.
53Disconnect the electrical harness from the TXV connector.
54Remove the bolt that attaches the electrical harness ground terminal to the body in the TXV area
55Release the clips that attach the electrical harness to the body in the front RH frame rail area.
56Remove and discard the bolt that attaches the electrical harness ground terminal to the body in the front RH frame rail area.
57Release the clips that attach the electrical harness to the body in the RH headlight area.
58Disconnect the electrical harness from the RH headlight connector.
59Partially close all doors.
60Remove the wheel chocks.
61With an assistant, move the vehicle to a lift.
Caution:
The vehicle is safely pushed for only a very short distance and at a very slow speed.
62Remove the front LH and front RH wheels. See Wheel (Remove and Install).
63Remove the front LH and front RH arch liners. See Wheel Arch Liner - Front - LH (Remove and Replace).
64Disconnect the electrical harness from the connectors in the front RH fascia area.
65Release the clips that attach the electrical harness to the body at the front of the front RH wheel liner area.
66Disconnect the electrical harness from the connector at the front of the front RH wheel liner area.
67Release the clips that attach the electrical harness to the body at the rear of the front RH wheel liner area.
68Disconnect the electrical harness from the front RH side repeater lamp connector.
69Disconnect the electrical harness from the connectors in the front LH fascia area.
70Disconnect the electrical harness from the front end module connector.
71Release the clips that attach the electrical harness to the body in the front LH wheel liner area.
72Disconnect the electrical harness from the connectors at the front of the front LH wheel liner area.
73Release the clips that attach the electrical harness to the body in the front LH wheel area.
74Disconnect the electrical harness from the front LH side repeater lamp connector.
75Lower the vehicle.
76Release the clips that attach the electrical harness to the body in the front RH frame area.
77Release the clips that attach the electrical harness to the body in the bulkhead area.
78Disconnect the electrical harness from the connectors in the bulkhead area.
79Release the clips that attach the electrical harness to the body in the LH frame rail area.
80Route the LH side of the electrical harness from the wheel liner, through the underhood storage unit area, and to the front body controller module area.
81Route the RH side of the electrical harness from the wheel liner, through the underhood storage unit area, and to the front body controller module area.
82Remove the electrical harness from the vehicle.

Install

  1. Install the electrical harness into the vehicle.
  2. Route the RH side of the electrical harness from the front body controller module area, through the underhood storage unit area, and to the RH wheel liner.
  3. Route the LH side of the electrical harness from the front body controller module area, through the underhood storage unit area, and to the LH wheel liner.
  4. Fasten the clips that attach the electrical harness to the body in the LH frame rail area.
  5. Connect the electrical harness to the connectors in the bulkhead area.
  6. Fasten the clips that attach the electrical harness to the body in the bulkhead area.
  7. Fasten the clips that attach the electrical harness to the body in the front RH frame area.
  8. Raise the vehicle.
  9. Connect the electrical harness to the front LH side repeater lamp connector.
  10. Fasten the clips that attach the electrical harness to the body in the front LH wheel area.
  11. Connect the electrical harness to the connectors at the front of the front LH wheel liner area.
  12. Fasten the clips that attach the electrical harness to the body at the front LH wheel liner area.
  13. Connect the electrical harness to the front end module connector.
  14. Connect the electrical harness to the connectors in the front LH fascia area.
  15. Connect the electrical harness to the front RH side repeater lamp connector.
  16. Fasten the clips that attach the electrical harness to the body at the rear of the front RH wheel liner area.
  17. Connect the electrical harness to the connector at the front of the front RH wheel liner area.
  18. Fasten the clips that attach the electrical harness to the body at the front of the front RH wheel liner area.
  19. Connect the electrical harness to the connectors in the front RH fascia area.
  20. Install the front LH and front RH arch liners. See Wheel Arch Liner - Front - LH (Remove and Replace).
  21. Install the front LH and front RH wheels. See Wheel (Remove and Install).
  22. With an assistant, move the vehicle from the lift.
    Caution:
    The vehicle is safely pushed for only a very short distance and at a very slow speed.
  23. Place wheel chocks on both rear wheels.
  24. Open the front LH and front RH doors.
  25. Connect the electrical harness to the RH headlight connector.
  26. Fasten the clips that attach the electrical harness to the body in the RH headlight area.
  27. Install a new bolt to attach the electrical harness ground terminal to the body in the front RH frame rail area.
    Torque 8 Nm
  28. Fasten the clips that attach the electrical harness to the body in the front RH frame rail area.
  29. Install the bolt that attaches the electrical harness ground terminal to the body in the TXV area
    Torque 9 Nm
  30. Connect the electrical harness to the TXV connector.
  31. Fasten the clips that attach the electrical harness to the body in the HVAC plenum duct area.
  32. Connect the electrical harness to the LH headlight connector.
  33. Connect the electrical harness to the steering rack connectors and the connectors in the front LH frame rail area.
  34. Install new bolts (x4) to attach the electrical harness ground terminals to the body in the front LH frame rail area.
    Torque 8 Nm
  35. Fasten the clips that attach the electrical harness to the body in the front LH frame rail area.
  36. Connect the electrical harness to the ABS unit connector.
  37. Connect the electrical harness to the brake booster connector.
  38. Connect the electrical harness to the connectors (x3) in the brake booster area.
  39. Fasten the clip that attaches the electrical harness to the body in the brake booster area.
  40. Move the LH side of the electrical harness in through the bulkhead.
  41. Connect the electrical harness to the LH body controller module connector.
  42. Connect the inline electrical harness connector X909, and then attach it to the LH body controller module.
  43. Install the power cable of the electrical harness to the LH body controller module, and then install a new nut to attach the power cable to the module.
    Torque 8.5 Nm
  44. Move the RH side of the electrical harness in through the bulkhead.
  45. Connect the electrical harness to the car computer connectors (x7).
  46. Fasten the clips that attach the electrical harness to the car computer.
  47. Connect the inline electrical harness connector, and then attach it to the RH body controller module.
  48. Raise the RH body controller module into position, and install a new nut to attach the module to the A-pillar.
    Torque 6 Nm
  49. Install the power cables of the electrical harness to the RH body controller module, and then install the new nuts (x2) to attach the power cables to the module.
    Torque 8.5 Nm
  50. Connect the electrical harness to the RH body controller module connector.
  51. Install the HVAC plenum inner duct to the body, and then install the fasteners that attach the inner duct to the body.
  52. Install the HVAC plenum outer duct onto the HVAC plenum inner duct, and then fasten the clips that attach the outer duct to the inner duct.
  53. Install the 12V battery bracket. See Bracket - 12V Battery (RWD) (Remove and Replace).
  54. Install the front body controller module to the body, and then install the bolt that attaches the ground strap to the lower rear of the module.
    Torque 9 Nm
  55. Install the ground strap to the lower right side of the front body controller module, and then install the bolt that attaches the ground strap to the module
    Torque 9 Nm
  56. Install the ground strap to the upper rear of the front body controller module, and then install the bolt that attaches the ground strap to the module.
    Torque 9 Nm
  57. Install the lower busbar onto the stud, and then fasten the clips that attach the bottom of the front body controller module to the body.
  58. Install the bolts that attach the front body controller module to the body.
    Torque 10 Nm
    Torque 10 Nm
  59. Install new nuts (x6) and new bolt to attach the power and ground cables to the front body controller module.
    Torque 8.5 Nm
    Torque 8.5 Nm
    Note: Make sure that the terminal lugs fit in their channels neatly.
  60. Connect the main front harness to the front body controller module connectors.
  61. Visually inspect that the power and the ground cables exit the front body controller module neatly in their respective channels, and parallel to each other.
    Caution:
    Make sure that no cables or wires will be pinched when the front body controller module cover is installed.
  62. Install the front body controller module cover to the front body controller module, and then install the bolts that attach the cover to the module.
    Torque 6 Nm
  63. Fasten the clip that attaches the suction/liquid lines to the body near the TXV.
  64. Connect the thermal harness to the front body controller module connector.
  65. Install the thermal harness cover to the front body controller module, and then install the bolt that attaches the cover to the module.
    Torque 6 Nm
  66. Install the wiper motor assembly. See Wiper Motor (Remove and Replace).
  67. Install the nut that attaches the 12V battery rear hook tie down.
  68. Install the 12V auxiliary battery. SeeBattery - 12V (Remove and Replace).
  69. Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
  70. Install the RH air wave duct. See Duct - Air Wave - RH (Remove and Replace).
  71. Install the RH footwell duct. See Duct - Footwell - RH (Remove and Replace).
  72. Install the glove box. See Glove Box (LHD) (Remove and Replace).
  73. Install the main instrument panel decor. See Decor Trim - Instrument Panel - Main (Remove and Replace).
  74. Install the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace)
  75. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  76. Fasten the clips that attach the footrest.
  77. Install the driver knee airbag. See Airbag - Knee - Driver (Remove and Install).
  78. Install the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  79. Connect 12V power. See 12V Power (Disconnect and Connect).
  80. Remove the wheel chocks.
  81. Close the hood.
  82. Close the front LH and front RH doors.
1Install the electrical harness into the vehicle.
2Route the RH side of the electrical harness from the front body controller module area, through the underhood storage unit area, and to the RH wheel liner.
3Route the LH side of the electrical harness from the front body controller module area, through the underhood storage unit area, and to the LH wheel liner.
4Fasten the clips that attach the electrical harness to the body in the LH frame rail area.
5Connect the electrical harness to the connectors in the bulkhead area.
6Fasten the clips that attach the electrical harness to the body in the bulkhead area.
7Fasten the clips that attach the electrical harness to the body in the front RH frame area.
8Raise the vehicle.
9Connect the electrical harness to the front LH side repeater lamp connector.
10Fasten the clips that attach the electrical harness to the body in the front LH wheel area.
11Connect the electrical harness to the connectors at the front of the front LH wheel liner area.
12Fasten the clips that attach the electrical harness to the body at the front LH wheel liner area.
13Connect the electrical harness to the front end module connector.
14Connect the electrical harness to the connectors in the front LH fascia area.
15Connect the electrical harness to the front RH side repeater lamp connector.
16Fasten the clips that attach the electrical harness to the body at the rear of the front RH wheel liner area.
17Connect the electrical harness to the connector at the front of the front RH wheel liner area.
18Fasten the clips that attach the electrical harness to the body at the front of the front RH wheel liner area.
19Connect the electrical harness to the connectors in the front RH fascia area.
20Install the front LH and front RH arch liners. See Wheel Arch Liner - Front - LH (Remove and Replace).
21Install the front LH and front RH wheels. See Wheel (Remove and Install).
22With an assistant, move the vehicle from the lift.
Caution:
The vehicle is safely pushed for only a very short distance and at a very slow speed.
23Place wheel chocks on both rear wheels.
24Open the front LH and front RH doors.
25Connect the electrical harness to the RH headlight connector.
26Fasten the clips that attach the electrical harness to the body in the RH headlight area.
27Install a new bolt to attach the electrical harness ground terminal to the body in the front RH frame rail area.
Torque 8 Nm
28Fasten the clips that attach the electrical harness to the body in the front RH frame rail area.
29Install the bolt that attaches the electrical harness ground terminal to the body in the TXV area
Torque 9 Nm
30Connect the electrical harness to the TXV connector.
31Fasten the clips that attach the electrical harness to the body in the HVAC plenum duct area.
32Connect the electrical harness to the LH headlight connector.
33Connect the electrical harness to the steering rack connectors and the connectors in the front LH frame rail area.
34Install new bolts (x4) to attach the electrical harness ground terminals to the body in the front LH frame rail area.
Torque 8 Nm
35Fasten the clips that attach the electrical harness to the body in the front LH frame rail area.
36Connect the electrical harness to the ABS unit connector.
37Connect the electrical harness to the brake booster connector.
38Connect the electrical harness to the connectors (x3) in the brake booster area.
39Fasten the clip that attaches the electrical harness to the body in the brake booster area.
40Move the LH side of the electrical harness in through the bulkhead.
41Connect the electrical harness to the LH body controller module connector.
42Connect the inline electrical harness connector X909, and then attach it to the LH body controller module.
43Install the power cable of the electrical harness to the LH body controller module, and then install a new nut to attach the power cable to the module.
Torque 8.5 Nm
44Move the RH side of the electrical harness in through the bulkhead.
45Connect the electrical harness to the car computer connectors (x7).
46Fasten the clips that attach the electrical harness to the car computer.
47Connect the inline electrical harness connector, and then attach it to the RH body controller module.
48Raise the RH body controller module into position, and install a new nut to attach the module to the A-pillar.
Torque 6 Nm
49Install the power cables of the electrical harness to the RH body controller module, and then install the new nuts (x2) to attach the power cables to the module.
Torque 8.5 Nm
50Connect the electrical harness to the RH body controller module connector.
51Install the HVAC plenum inner duct to the body, and then install the fasteners that attach the inner duct to the body.
52Install the HVAC plenum outer duct onto the HVAC plenum inner duct, and then fasten the clips that attach the outer duct to the inner duct.
53Install the 12V battery bracket. See Bracket - 12V Battery (RWD) (Remove and Replace).
54Install the front body controller module to the body, and then install the bolt that attaches the ground strap to the lower rear of the module.
Torque 9 Nm
55Install the ground strap to the lower right side of the front body controller module, and then install the bolt that attaches the ground strap to the module
Torque 9 Nm
56Install the ground strap to the upper rear of the front body controller module, and then install the bolt that attaches the ground strap to the module.
Torque 9 Nm
57Install the lower busbar onto the stud, and then fasten the clips that attach the bottom of the front body controller module to the body.
58Install the bolts that attach the front body controller module to the body.
Torque 10 Nm
Torque 10 Nm
59Install new nuts (x6) and new bolt to attach the power and ground cables to the front body controller module.
Torque 8.5 Nm
Torque 8.5 Nm
Note: Make sure that the terminal lugs fit in their channels neatly.
60Connect the main front harness to the front body controller module connectors.
61Visually inspect that the power and the ground cables exit the front body controller module neatly in their respective channels, and parallel to each other.
Caution:
Make sure that no cables or wires will be pinched when the front body controller module cover is installed.
62Install the front body controller module cover to the front body controller module, and then install the bolts that attach the cover to the module.
Torque 6 Nm
63Fasten the clip that attaches the suction/liquid lines to the body near the TXV.
64Connect the thermal harness to the front body controller module connector.
65Install the thermal harness cover to the front body controller module, and then install the bolt that attaches the cover to the module.
Torque 6 Nm
66Install the wiper motor assembly. See Wiper Motor (Remove and Replace).
67Install the nut that attaches the 12V battery rear hook tie down.
68Install the 12V auxiliary battery. SeeBattery - 12V (Remove and Replace).
69Install the underhood storage unit. See Underhood Storage Unit (Remove and Replace).
70Install the RH air wave duct. See Duct - Air Wave - RH (Remove and Replace).
71Install the RH footwell duct. See Duct - Footwell - RH (Remove and Replace).
72Install the glove box. See Glove Box (LHD) (Remove and Replace).
73Install the main instrument panel decor. See Decor Trim - Instrument Panel - Main (Remove and Replace).
74Install the front passenger knee airbag. See Airbag - Knee - Front Passenger (Remove and Replace)
75Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
76Fasten the clips that attach the footrest.
77Install the driver knee airbag. See Airbag - Knee - Driver (Remove and Install).
78Install the LH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
79Connect 12V power. See 12V Power (Disconnect and Connect).
80Remove the wheel chocks.
81Close the hood.
82Close the front LH and front RH doors.