Brake Pad Kit - Rear (Base Brakes) (Remove and Replace)

Correction code 3301080233010802
  • 1134520-00-A Kit, EPB Release, Handheld
  • 1129348-00-AXP-10 Power Supply, XP-10

SPECIAL TOOLS

Kit, EPB Release, Handheld (1134520-00-A)
XP-10 Power Supply, XP-10 (1129348-00-A)

Remove

  1. Remove the LH rear wheel. See Wheel (Remove and Install).
  2. Use Toolbox to place the vehicle into EPB Service Mode. See Release Parking Brake Using Toolbox.
  3. Remove the bolts that attach the LH rear brake caliper to the LH rear brake caliper bracket.
    Torque 26.5 Nm
  4. Use a brake caliper S-hook to hang the LH rear brake caliper on the body.
  5. Remove the brake pads from the LH rear brake caliper bracket.
  6. Remove the caliper abutment clips from the LH rear brake caliper bracket.
  7. Repeat step 1 through step 10 for the RH rear brake pad removal.
1Remove the LH rear wheel. See Wheel (Remove and Install).
2Use Toolbox to place the vehicle into EPB Service Mode. See Release Parking Brake Using Toolbox.
3Remove the bolts that attach the LH rear brake caliper to the LH rear brake caliper bracket.
Torque 26.5 Nm
4Use a brake caliper S-hook to hang the LH rear brake caliper on the body.
5Remove the brake pads from the LH rear brake caliper bracket.
6Remove the caliper abutment clips from the LH rear brake caliper bracket.
7Repeat step 1 through step 10 for the RH rear brake pad removal.

Install

  1. Install the caliper abutment clips.
  2. Apply an even layer of Silaramic lubricant to the abutment clips.
  3. Install the brake pads on the LH rear brake caliper bracket.
    Tip: During installation, press the brake pads toward the brake rotor.
    Note: Use the caliper spreader tool to push the caliper piston back into the caliper, if more room is needed.
  4. Install the bolts that attach the LH rear brake caliper to the LH rear brake caliper bracket.
    Torque 26.5 Nm
  5. Install the LH rear wheel. See Wheel (Remove and Install).
  6. Repeat step 1 through step 5 for the RH rear brake pad installation.
  7. Apply the parking brake by touching the Park button on the touchscreen.
  8. Pump the brake pedal to seat the pads against the brake rotor until the brake pedal feels firm.
  9. Check the brake fluid level and top off the brake fluid reservoir, if necessary.
  10. Perform vehicle road test using a series of ABS-active stops and make sure proper brake pedal feel and performance is achieved.
1Install the caliper abutment clips.
2Apply an even layer of Silaramic lubricant to the abutment clips.
3Install the brake pads on the LH rear brake caliper bracket.
Tip: During installation, press the brake pads toward the brake rotor.
Note: Use the caliper spreader tool to push the caliper piston back into the caliper, if more room is needed.
4Install the bolts that attach the LH rear brake caliper to the LH rear brake caliper bracket.
Torque 26.5 Nm
5Install the LH rear wheel. See Wheel (Remove and Install).
6Repeat step 1 through step 5 for the RH rear brake pad installation.
7Apply the parking brake by touching the Park button on the touchscreen.
8Pump the brake pedal to seat the pads against the brake rotor until the brake pedal feels firm.
9Check the brake fluid level and top off the brake fluid reservoir, if necessary.
10Perform vehicle road test using a series of ABS-active stops and make sure proper brake pedal feel and performance is achieved.